Marking Aluminum.

ALUMINUM MARKING
Or 
(MARKING ALUMINUM)

NOW PERMANENTLY MARK ALUMINUM TOOLS, PARTS, INSTRUMENTS AND EQUIPMENT WITH NAMES, NUMBERS, DESIGNS OR  TRADEMARKS IN SECONDS
FOR LESS THAN ONE CENT PER MARK.

Here Are Examples Of Aluminum Marking That You Can Easily
Do In Your Own Shop In Just Seconds!  Now All You Do Is Create Your
Own Design, Logo, Brand Name Or Trademark And Then Put It On Your
Tools, Parts Or Equipment For Less Than A Cent Per Mark.  It Is Easy,
Quick, Inexpensive And Professional! 
 And YOU Can Do It!

See a Video of Metal Marking - Click Here

 

tools

tools

tools

Etch Aluminum Blades

Etch Black On 1/4" Drill Bit 

 Etch Deep Marks 

tools

tools

tools

Black Marks In Seconds

Etching Tools & Gauges

Deep Etch BLACK Mark


HERE IS HOW TO MARK ALUMINUM OR
ANY TYPE OF METAL

 Using Dura-Film Stencils And 
The Etch-O-Matic Metal Marking Kits.

Here Is The Quick, Easy And Inexpensive Way To Mark Your Tools, Parts Or Even A Knife.

First Make Your Artwork On Your Computer With Our New Ultra Violet Stencil Makers.  When Finished It Should Look Like This One. Or You Can Use Our Regular Die Impressed Stencils Which Are Included In Every Kit By Simply Typing On Them.

Computer

Next Place The Stencil On Your Tool, Part Or Knife Blade
And Use A Small Piece Of Scotch Tape To Hold It In Position. 

etching knife

When Ready Wet The Head Of The Etch-O-Matic With Electrolyte And Place It On The Stencil.  After Everything Is Lined Up Correctly Just Touch The Blade With The Ground Wire
(Shown With Alligator Clip) For A Few Seconds And Your Mark Is Complete.

knife

Here Is Your Mark.  It Is Black On Stainless Steel But You Can Also Make 
Deep Etch Marks Down To About .003" And They Can Be "Clear" Or Black.

acid etched mark

Now You Can See Just How Easy It Is To Put Your Own Mark On
Anything Metal Including Tools, Parts, Instruments Or Even Knives.

HERE IS MARKING BY ETCH-O-MATIC.

REGULAR MARKING
eom

MARKING WITH GROUND PLATE — Simply Lay the Tool or Part on the Ground Plate and Touch ETCH-O-MATIC to it for a Few Brief Seconds and Your Mark is Permanently Etched Into the Surface.

MARKING ROUND SURFACES
Etch

MARKING ROUND SURFACES — Drill Bits, Milling Cutters, Tubing, Pipe or nearly anything Round can be Easily Marked by "Rolling"  the Mark on as Shown Above.

DEEP MARKING
Etch

MAKES DEEP ETCH MARKS ETCH-O- MATIC Marks many Metals as Deep as .003" with Deep Etch Adapter Clip, a Mark that can only be Removed by Grinding a Major Part of the Surface Away.

 

      If it is Made of Metal
        ETCH-O-MATIC
    Can Mark It And Even
               Put Your
          TRADEMARK
    On It In Just Seconds!

 


tools
PERMANENTLY MARKING ALUMINUM
 OR ANY METAL...IN SECONDS!

MARKING INTO THE SURFACE — ETCH-O-MATIC will Mark into the surface of Aluminum or Anything made of Metal, including Tools, Instruments, Equipment or Manufactured Parts, anything that can be Typed, Written, Drawn or Photo Processed on a Special Stencil. This includes Names, Numbers, Designs, Logos, Trademarks or even Your Own Signature. Using an Electro- Chemical principle, the New ETCH-O-MATIC can Mark as Deep as .003" of an Inch in Less than 30 Seconds or Mark the Hardest Tool Steel and Carbides almost Instantly. It marks any Flat or Round Metal Surface down to 1/16" Diameter and any Metal Thickness from Thin Foil up to the Largest Castings easily. Most Marks (which look like Printing or Engraving) take about 3 to 20 Seconds (the Longer Dwell Times are for Deep Etching) and are Permanently Etched into the Tool or Manufactured Part.

FAST AND VERY EASY TO USE!

ETCH-O-MATIC is FAST and EASY TO USE. Anyone in Your Organization can become an EXPERT in JUST MINUTES and produce Professional Looking Marks Quickly. In Fact, Etch-O-Matic is by Far the Very Easiest Marking System to Learn that is Available Today!  Also, You will find that ETCH-O-MATIC is not only the Fastest way to make Permanent Marks on Anything Metal, but is by Far the LEAST EXPENSIVE method on the Market Today. Your Marks will Cost just Fractions of a Cent to Produce and You will be Extremely Pleased with the Result.

                               RESULTS LOOK LIKE LASER MARKS

Most Marks will Compare Favorably with Laser Marking on Metal and are Easier and Sometimes Even Faster to Make.  In Fact You have Seen Marks made by Etch-O-Matic hundreds of times before but probably did Not Realize it since the Marks are Used so often in Commerce Today.  If you have ever seen a Feeler Gauge, Drill Bit, Milling Cutter, Saw Blade, Knife Blade, Ball Bearing Race, Carbide Cutter or Thousands of other types of Metal Tools, Parts, Instruments or Equipment then You have probably seen Marks made by Etch-O-Matic.  In fact, we have Marks in a good Percentage of all of the Cars, Trucks, Commercial and Military Aircraft, Submarines, Hospital Surgical Instruments and Implant Devices and we even have Marks in the Nose Cone of the Space Shuttle.  (Yes, NASA called and said that they used an Etch-O-Matic to Mark an Inspection Date and Number in the Nose Cone of the Space Shuttles.)

BASICALLY, THE ETCH-O-MATIC ALUMINUM MARKING SYSTEM has been Proven Over and Over again during our 36 Years in Business as the Best Way to Permanently Mark Aluminum or Any Metal.          


Here Are Etch-O-Matic Aluminum Marking Kits That Are
Combined With The New STENCIL-MAKERS For
SPECIAL COMBO OFFERS YOU MUST SEE!

With Prices Starting As Low As $79.95
No One Bests These Prices!

Click Below To See The Complete Etch-O-Matic Line
Of Marking Kits (On Special Today) 
Along With TODAY'S SPECIAL PRICES!

CLICK HERE FOR MAIN PAGE!


To Contact Us Just Call: 800-775-0797 During Pacific Coast
 Time
From 8:00 A.M. To 4:30 P.M. And A Real Person Will Talk With You
And Explain Anything You Want To Know. 
Email Us
Or FAX At 1-360-985-2996

P.O. Box 200 / 500 Wilcox Road
Salkum, WA 98582
Email - Click Here
 Phone: 1.800.775.0797
Fax: 1.360.985.2996