We've been in business for over 41 years. ~~~ Etch-O-Matic is a Trademark of
Martronics Corp.
~~~
� 2007 Martronics Corporation
Now Permanently Mark Anything Metal In Seconds!
With The New Etch-O-Matic Metal Marking KitsYou Can Permanently Mark Tools, Parts, Instruments And Equipment With Your Names, Numbers, Designs Or Trademarks In Your Shop In JustSeconds For Less Than One Cent Per Mark
Below Are Examples Of Permanent Metal Etching That You Can Easily Do In Your Own Shop! Simply Create Your Own Copy, Designs Or Trademark On Your Computer And Put The Marks On Your Tools,
PartsOr Equipment In Just Seconds! Marking Is Easy, Quick, Inexpensive And Professional! And You Can Do It!
SEE HOW YOU CAN EASILY ETCH METAL TOOLS, PARTS, KNIVES PERMANENTLY IN SECONDS!
ETCH-O-MATIC will Etch into the Surface of Anything made of Metal, including Tools, Instruments, Equipment or Metal Parts, anything that can be Typed or Photo Processed on a Special Stencil. This includes Names, Numbers, Designs, Trademarks. Using an Electro- Chemical principle, the New ETCH-O-MATIC can Etch as Deep as .003" of an Inch in Less than 30 Seconds or Mark the Hardest Tool Steel and Carbides almost Instantly. It marks any Flat or Round Metal Surface down to 1/16" Diameter and any Metal Thickness from Thin Foil up to the Largest Castings easily. Most Marks (which look like Printing or Engraving) take about 3 to 20 Seconds (the Longer Dwell Times are for Deep Etching)and are Permanently Etched into the Tool or Manufactured Part.
MAKES MARKS QUICKLY AND EASILY! ETCH-O-MATIC is EASY TO USE. Anyone can become an EXPERT in JUST MINUTES and produce Professional Looking Marks In Seconds. Etch-O-Matic is the Very Easiest MarkingSystem to Learn that is Available Today! Also, You will find that ETCH-O-MATIC is by Far the LEAST EXPENSIVE method of Metal Marking on the Market Today. Your Marks will Cost Less than a Cent to Produce and You will be Pleased with the Result.
MARKING WITH GROUND PLATE � Simply Lay the Tool or Part on the Ground Plate and Touch ETCH-O-MATIC to it for a Few Brief Seconds and Your Mark is Permanently Etched Into the Surface.
MARKING ROUND SURFACES � Drill Bits, Milling Cutters, Tubing, Pipe or nearly anything Round can be Easily Marked by "Rolling" the Mark on as Shown Above.
MAKES DEEP ETCH MARKS� ETCH-O- MATIC Marks many Metals as Deep as .003" with Deep Etch Adapter Clip, a Mark that can only be Removed by Grinding a Major Part of the Surface Away.
BASICALLY, ETCH-O-MATIC and the Electro-Chemical Marking System has been Proven Over and Over again during our 36 Years in Business as the Best Way to Permanently Mark Anything Metal.
HOW TO USE A DURA-FILM STENCIL.
Here Is a Quick, Easy And Inexpensive Way To Mark Metal Tools, Parts Or Knives.
Create Your Artwork On Your Computer With Our New Ultra Violet Stencil-Makers. (As Shown Below). Or You Can Use Our Regular Die Impressed Stencils Which Are Included In Every Kit - Just Simply Type On Them.
Next Place The Stencil On Your Tool, Part Or Knife Blade, and Use a Small Piece Of Scotch Tape To Hold It In Position.
(NOTE: You Can Put The Stencil Directly On The
Etch-O-Matic For Marking Metal, But This Method Is Used For Exact Placement On An Item.)
When You are Ready Wet the Head of The Etch-O-Matic With Electrolyte, and Place It On The Stencil. Touch The Blade With The Ground Wire (Shown With Alligator Clip) For a Few Seconds and Your Mark Is Complete - it's just that simple!
The Mark Shown is Black On Stainless Steel But You Can Also Make Deep Etch Marks Down To About .003" and They Can Be "Clear" Or Black.
You Can See Just How Easy It Is To Put Your Own Mark On Anything Including Tools, Parts, Instruments Or Even Knives.
Permanently Marked...Here We Are Marking A Saw Blade Since It Is Large Enough To Make A Good Photo. You Simply Lay The Stencil On The Blade, Wet The Etch-O-Matic Pad (On Bottom) With Electrolyte, Then Place The Etch-O-Matic On The Stencil, Ground For A Few Seconds And Then Remove And Your Blade Is Permanently Marked.
Sample Of Typewriter Stencil That Comes In Each Kit Shown Above. We Have Typed "SAMPLE MARK" To Show You How It Would Look.
TYPEWRITER STENCILS
In Each Etch-O-Matic Kit There Is A FREE Package Of Stencils. They Are Prepared By Using A Typewriter Like The Sample Shown on the Left. This Is Quick, Easy And Cheap, As You Can Do It Yourself If You Have A Typewriter. The Marks Will Look Just Like You "Typed" In Black Letters On Your Parts.
You Can Make Your Own Dura-Film Stencils (With The Purchase Of A UV Stencil Maker Shown Below) As Shown Below Or Even Send Us Your Artwork And We Will Make Them For You. Contact Us By email, Fax or Phone For This.
HOW TO MAKE DURA-FILM STENCILS Now Make Dura-Film Stencils In About 3 Minutes.
(NOTE: We Are Using Large Type So It Will Photograph Easily.)
Your Artwork...First Make Your Copy On Your Computer. Here Is A Simple A B C Made Large To Show In The Photo.You Can Make Any Line Drawing, Logo, Trademark or Simple Message You Wish. There Is Not Much Limit Except Photos Are Difficult And Very Thin Lines Are Hard To Mark.
Transparency...Next Print Out Your Copy On A Transparency (Which Comes In The Kit) And Place The Transparency Copy On A Piece Of Unexposed Dura-Film Stencil (Which Comes In The Kit) And Finally Place A Glass Plate On Top.
U.V. Exposure Unit...Next Place Tray In The 440 Dura-Film Stencil Maker And Turn On Exposure Unit For About Three Minutes.
Develop Your Stencil...Next Remove Stencil And Develop For 30 Seconds To A Minute. Stencil Is Then Ready To Use To Mark Your Knives Or Anything Metal.
Permanently Marked...Here We Are Marking A Saw Blade Since It Is Large Enough To Make A Good Photo. You Simply Lay The Stencil On The Blade, Wet The Etch-O-Matic Pad (On Bottom) With Electrolyte, Then Place The Etch-O-Matic On The Stencil, Ground For A Few Seconds And Then Remove And Your Blade Is Permanently Marked.
ETCH-O-MATIC MAKES FOUR TYPES OF MARKS
Today's Special - 20% Coupon Included in COMBO KITS
Good For Kits or Supplies on Your NEXT ORDER.
We Do NOT Guarantee This Offer Will Be Available Tomorrow!
DON'T MISS IT!
Here Is A New Product Idea!
Now Use Your Metal Etching Stencils
Made For The Etch-O-Matic Above And ETCH GLASS!
Here Is A Great New Idea That Lets You Use The Stencils
You Make For Metal Etching...And Etch Almost Anything
Made Of Glass In Just Seconds. All You Do Is Create Your
Copy, Designs Or Artwork On YOUR Computer, Make A
Stencil (Like Above) And By Using Our New Glass Etching
Kits You Can Etch On Glass!
Would you like to be notified of special offers and new products? Would you like us to send you tips for expanding your etching business, or just more ways to enjoy your etching hobby? How about special members-only discounts? Try subscribing to our newsletter, and you'll get all these things and more.